₦88,700
You can also download the manual through the link below.
Studer RCC-02 and RCC-03 User Manual
The RCC-02 Remote Control Centre For Studer enables the user to supervise the system and to completely adapt it to the needs through the many parameter settings available on the Xtenders, on the VarioTracks and on the VarioStrings.
1 & 3 Phase SystemThanks to its digital display, the RCC-02 provides clear and comprehensive indications on the state of the system in the chosen language.
The device memorizes the events that occurred on an installation and therefore anticipates any future problems.
Date Time & Special Function
A SD card reader is available and allows parameters recording, as well as the uploading of various pre-settings and of all future updates.
Meant for wall mounting.
Dimension H x L x l: 170 x 168 x 43.5 mm.
Supplied with 2 m cable (max. 50m)
You can also download the manual through the link below.
Studer RCC-02 and RCC-03 User Manual
| Inverter | |
| Model | XTH 6000-48 |
| Nominal battery voltage | 48 Vdc |
| Input voltage range | 38 – 68 Vdc |
| Continuous power @ 25°C | 5000 VA |
| Power 30 min. @ 25°C | 6000 VA |
| Power 5 sec. @ 25°C | 15 kVA |
| Maximum load | Up to short-circuit |
| Asymmetric load | Up to Pcont. |
| Load detection (stand-by) | 2 to 25 W |
| Cos j | 0.1-1 |
| Maximum efficiency | 96 % |
| Consumption OFF/Stand-by/ON | 1.8 W / 2.2 W / 22 W |
| Output voltage | Pure sine wave 230 Vac (± 2 %) / 120 Vac (1) |
| Output frequency | Adjustable 45 – 60 Hz (1) ± 0.05 % (crystal controlled) |
| Harmonic distortion | < 2 % |
| Overload and short-circuit protection | Automatic disconnection with 3 time restart attempt |
| Overheat protection | Warning before shut-off – with automatic restart |
| Battery charger | |
| Charge Characteristic | 6 steps: Bulk, Absorption, Floating, Equalization, reduced floating, periodic absorption Number of steps, thresholds, end current and times completely adjustable with the RCC-02/-03 |
| Maximum charging current | 100 A |
| Temperature compensation | With BTS-01 or BSP 500/1200 |
| Power Factor Correction (PFC) | EN 61000-3-2 |
| General data | XTH 6000-48 |
| Input voltage range | 150 to 265 Vac / 50 to 140 Vac (1) |
| Input frequency | 45 to 65 Hz |
| Input current max. (transfer relay) / Output current max. | 50 Aac / 56 Aac |
| Transfer time | <15 ms |
| Multifunction contacts | 2 independent contacts (potential free 3 points, 16Aac / 5Adc) |
| Weight | 42 kg |
| Dimensions h/w/l [mm] | 230 / 300 / 500 |
| Protection index | IP20 |
| EU declaration of conformity | Low Voltage Directive (LVD) 2014/35/EU: – EN 50178:1997 Electromagnetic Compliance (EMC) Directive 2014/30/EU: – EN 62040-2:2006, EN 61000-3-2:2014, EN 61000-3-12:2011 |
| Operating temperature range | -20 to 55°C |
| Relative humidity in operation | 95 % without condensation |
| Ventilation | Forced from 55°C |
| Acoustic level | < 40 dB / < 45 dB (without/with ventilation) |
| Warranty | 5 years |
| ISO Certification | 9001:2008 / 14001:2004 |
| Accessories | |
| Remote control RCC-02 or RCC-03 | Adjustable with the RCC-02/-03 |
| Module Xcom-232i | Adjustable with the RCC-02/-03 |
| Communication sets Xcom-LAN / Xcom-GSM / Xcom-SMS | Adjustable with the RCC-02/-03 |
| Battery Status Processor BSP | Adjustable with the RCC-02/-03 |
| Remote Control Module RCM-10 (3 m) | Adjustable with the RCC-02/-03 |
| 2 aux. contacts module ARM-02 | |
| Cooling Module ECF-01 | |
| Battery temp. sensor BTS-01 (3 m) | Adjustable with the RCC-02/-03 |
| Communication cable for 3ph and // CAB-RJ45-8-2 | Adjustable with the RCC-02/-03 |
| Mounting frame X-Connect | |
© Copyright 2025 PRAG. All rights reserved. | Privacy Policy | Terms of Use | Sitemap
© Copyright 2025 PRAG. All rights reserved.
Privacy Policy | Terms of Use | Sitemap
The products, prices and promotions on this website are applicable to our customers only and are subject to change anytime.
